View MK3727H_232615.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MK3727H
LOW DRIVE 3.3 VOLT VCXO
Description
The MK3727H and MK3727J are low drive, low cost, single output 3.3 Volt VCXO and PLL clock synthesizers designed to replace expensive VCXOs and crystals. The patented on-chip Voltage Controlled Crystal Oscillator accepts a 0 to 3.3 V input voltage to cause the output clocks to vary by 115 ppm minimum. Using our analog Phase Locked Loop (PLL) techniques, the devices uses an external, fundamental mode 13.5 MHz pullable crystal input to produce output clocks of 27 MHz. The drive parameters are optimized for low EMI. The frequency of the on-chip VCXO is adjusted by an external control voltage input into pin VIN. Because VIN is a high-impedance input, it can be driven directly from an PWM RC integrator circuit.
Features
* Packaged in 8-pin SOIC * MK3727J has improved linearity and pull-curve
compared to the MK3727H
* Operating voltage of 3.3 V (5%) * Single pullable output clock of 24 to 36 MHz * Uses a fundamental mode 12 to 18 MHz pullable
crystal
* On-chip patented VCXO with pull range of 230 ppm
(minimum)
* VCXO tuning voltage of 0 to 3.3 V * Low-drive output stage to reduce EMI * Advanced, low-power, sub-micron CMOS process
The MK3727J is recommended for all new designs.
Block Diagram
VDD VIN
X1
X2 12 to 18 MHz Pullable Crystal
Voltage Controlled Crystal Oscillator
Frequency Clock Doubler
24 to 36 MHz
GND
MDS 3727H C
I n t e gra t e d C ir c u i t S ys t e m s
1
5 2 5 R a c e S t r e e t , S a n J o s e, C A 9 5 1 2 6 tel (408) 297-1201
Revision 902304
www.i cst .co m
MK3727H LOW DRIVE 3.3 VOLT VCXO
Pin Assignment
X1 VDD VIN GND 1 2 3 4 8 7 6 5 X2 GND NC CLK
8 Pin (150 mil) SOIC
Pin Descriptions
Pin Number
1 2 3 4 5 6 7 8
Pin Name
X1 VDD VIN GND CLK NC GND X2
Pin Type
Input Power Input Input Output -- Input Output
Pin Description
Crystal connection. Connect to a 12 to 18 MHz external pullable crystal. Connect to +3.3 V. Voltage input to VCXO. Zero to 3.3 V analog input which controls the oscillation frequency of the VCXO. Connect to ground. VCXO clock output. 2x input frequency. No connect. Do not connect to anything. Connect to ground. Crystal connection. Connect to a 12 to 18 MHz external pullable crystal.
MDS 3727H C
I n t e gra t e d C i r c u i t S y s t e m s
2
5 2 5 R a c e S tr e e t , S a n J o s e, C A 9 5 1 2 6 tel (408) 297-1201
Revision 902304
w w w.i c s t . c o m
MK3727H LOW DRIVE 3.3 VOLT VCXO
External Component Selection
The MK3727H requires a minimum number of external components for proper operation.
Crystal Tuning Load Capacitors
The crystal traces should include pads for small fixed capacitors, one between X1 and ground, and another between X2 and ground. Stuffing of these capacitors on the PCB is optional. The need for these capacitors is determined at system prototype evaluation, and is influenced by the particular crystal used (manufacture and frequency) and by PCB layout. The typical required capacitor value is 1 to 4 pF. To determine the need for and value of the crystal adjustment capacitors, you will need a PC board of your final layout, a frequency counter capable of about 1 ppm resolution and accuracy, two power supplies, and some samples of the crystals which you plan to use in production, along with measured initial accuracy for each crystal at the specified crystal load capacitance, CL. To determine the value of the crystal capacitors: 1. Connect VDD of the MK3727H to 3.3 V. Connect pin 3 of the MK3727H to the second power supply. Adjust the voltage on pin 3 to 0V. Measure and record the frequency of the CLK output. 2. Adjust the voltage on pin 3 to 3.3 V. Measure and record the frequency of the same output. To calculate the centering error:
Decoupling Capacitor
A decoupling capacitor of 0.01F must be connected between VDD (pin 2) and GND (pin 4 & 7), as close to these pins as possible. For optimum device performance, the decoupling capacitor should be mounted on the component side of the PCB. Avoid the use of vias in the decoupling circuit.
Series Termination Resistor
Use series termination when the PCB trace between the clock outputs and the loads are over 1 inch. To series terminate a 50 trace (a commonly used trace impedance), place a 33 resistor in series with the clock line, as close to the clock output pin as possible. The nominal impedance of the clock output is 20.
Quartz Crystal
The MK3727H VCXO function consists of the external crystal and the integrated VCXO oscillator circuit. To assure the best system performance (frequency pull range) and reliability, a crystal device with the recommended parameters (as described in application note MAN05) must be used, and the layout guidelines discussed in the following section must be followed. The frequency of oscillation of a quartz crystal is determined by its "cut" and by the load capacitors connected to it. The MK3727H incorporates on-chip variable load capacitors that "pull" (change) the frequency of the crystal. The crystal specified for use with the MK3727H is designed to have zero frequency error when the total of on-chip + stray capacitance is 14 pF. The external crystal must be connected as close to the chip as possible and should be on the same side of the PCB as the MK3727H. There should be no vias between the crystal pins and the X1 and X2 device pins. There should be no signal traces underneath or close to the crystal.
6 ( f 3.0V - f t arg et ) + ( f 0V - f t arg et ) Error = 10 x ------------------------------------------------------------------------------ - error xtal f t arg et
Where: ftarget = nominal crystal frequency errorxtal =actual initial accuracy (in ppm) of the crystal being measured If the centering error is less than 25 ppm, no adjustment is needed. If the centering error is more than 25 ppm negative, the PC board has excessive stray capacitance and a new PCB layout should be considered to reduce stray capacitance. (Alternately, the crystal may be re-specified to a higher load capacitance. Contact ICS MicroClock for details.) If the centering error is more than 25 ppm positive, add identical fixed centering capacitors from each crystal pin to ground. The value for each of these caps (in pF) is given by:
MDS 3727H C
I n t e gra t e d C i r c u i t S y s t e m s
3
5 2 5 R a c e S tr e e t , S a n J o s e, C A 9 5 1 2 6 tel (408) 297-1201
Revision 902304
w w w.i c s t . c o m
MK3727H LOW DRIVE 3.3 VOLT VCXO
External Capacitor = 2 x (centering error)/(trim sensitivity) Trim sensitivity is a parameter which can be supplied by your crystal vendor. If you do not know the value, assume it is 30 ppm/pF. After any changes, repeat the measurement to verify that the remaining error is acceptably low (typically less than 25 ppm).
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the MK3727H. These ratings, which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range.
Item
Supply Voltage, VDD All Inputs and Outputs Ambient Operating Temperature Storage Temperature Soldering Temperature 7V
Rating
-0.5 V to VDD+0.5 V 0 to +70C -65 to +150C 260C
Recommended Operation Conditions
Parameter
Ambient Operating Temperature Power Supply Voltage (measured in respect to GND) Reference crystal parameters
Min.
0 +3.13
Typ.
Max.
+70 +3.46
Units
C
V
Refer to MAN05
MDS 3727H C
I n t e gra t e d C i r c u i t S y s t e m s
4
5 2 5 R a c e S tr e e t , S a n J o s e, C A 9 5 1 2 6 tel (408) 297-1201
Revision 902304
w w w.i c s t . c o m
MK3727H LOW DRIVE 3.3 VOLT VCXO
DC Electrical Characteristics
VDD=3.3 V 5% , Ambient temperature 0 to +70C, unless stated otherwise
Parameter
Operating Voltage Output High Voltage Output Low Voltage Output High Voltage (CMOS Level) Operating Supply Current Short Circuit Current VIN, VCXO Control Voltage Nominal output impedance
Symbol
VDD VOH VOL VOH IDD IOS VIA ZOUT
Conditions
IOH = -8 mA IOL = 8 mA IOH = -4 mA No load
Min.
3.13 2.4
Typ.
Max.
3.46 0.5
Units
V V V V
VDD-0.4 10 25 0 20 3.3
mA mA V
AC Electrical Characteristics
VDD = 3.3 V 5%, Ambient Temperature 0 to +70 C, unless stated otherwise
Parameter
Crystal Pullability VCXO Gain Output Rise Time Output Fall Time Output Clock Duty Cycle Maximum Output Jitter, short term
Symbol
FP tOR tOF tD tJ
Conditions
0V< VIN < 3.3 V, Note 1 VIN = VDD/2 + 1 V, Note 1 0.3 to 3.0 V, CL=10 pF 3.0 to 0.3 V, CL=10 pF Measured at VDD/2, CL=10 pF CL=10 pF
Min.
+ 115
Typ.
120 3.0 3.0
Max. Units
ppm ppm/V ns ns 55 % ps
45 100
Note 1: External crystal device must conform with Pullable Crystal Specifications listed in MAN05.
Thermal Characteristics
Parameter
Thermal Resistance Junction to Ambient
Symbol
JA JA JA JC
Conditions
Still air 1 m/s air flow 3 m/s air flow
Min.
Typ.
150 140 120 40
Max. Units
C/W C/W C/W C/W
Thermal Resistance Junction to Case
MDS 3727H C
I n t e gra t e d C i r c u i t S y s t e m s
5
5 2 5 R a c e S tr e e t , S a n J o s e, C A 9 5 1 2 6 tel (408) 297-1201
Revision 902304
w w w.i c s t . c o m
MK3727H LOW DRIVE 3.3 VOLT VCXO
Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Narrow Body)
Package dimensions are kept current with JEDEC Publication No. 95
Millimeters
8
Inches Min Max
Symbol
Min
Max
E INDEX AREA
H
12 D
A A1 B C D E e H h L
1.35 1.75 0.10 0.25 0.33 0.51 0.19 0.25 4.80 5.00 3.80 4.00 1.27 BASIC 5.80 6.20 0.25 0.50 0.40 1.27 0 8
.0532 .0688 .0040 .0098 .013 .020 .0075 .0098 .1890 .1968 .1497 .1574 0.050 BASIC .2284 .2440 .010 .020 .016 .050 0 8
A A1
h x 45 C
-Ce
B SEATING PLANE L
.10 (.004)
C
Ordering Information
Part / Order Number
MK3727H MK3727HTR MK3727J MK3727JTR
Marking
MK3727H MK3727H MK3727J MK3727J
Shipping Packaging
Tubes Tape and Reel Tubes Tape and Reel
Package
8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Temperature
0 to +70 C 0 to +70 C 0 to +70 C 0 to +70 C
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments.
MDS 3727H C
I n t e gra t e d C i r c u i t S y s t e m s
6
5 2 5 R a c e S tr e e t , S a n J o s e, C A 9 5 1 2 6 tel (408) 297-1201
Revision 902304
w w w.i c s t . c o m

▲Up To Search▲

Price & Availability of MK3727H

	To Download MK3727H Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .